Chassis & Suspension | Camburg Engineering

KINETIK Rear Chassis Upper & Lower Link Mounts

scott — Thu, 29 Jun 2023 21:16:27 +0000

Building a pre-runner or race truck from the ground up or looking to upgrade your existing truck? Our KINETIK rear chassis lower & upper link mounts take the headache out of designing the rear suspension. We designed this based around our proven TT/6100 chassis and geometry and gives you a great starting point to build from or easily graft into an existing tube chassis or frame rails. By MIG welding these we’re able to bring the cost down and offer something a little more affordable without compromising quality.

The upper mounts are designed for 1-1/4″ heims (JMX-16T) using 5/8″ bolts and the lowers mounts for 1″ uniballs (AIN-16T) using a 3/4″ bolts. You can use these with our 48″, 55″ or 60″ lower links depending on the wheelbase and shock locations you’re looking for. We use 3/16″ and 1/8″ 4130 chromoly to build these with overlay plates at the pivot points for added strength/thickness.

CAD designed and laser cut
4130 chromoly plate
Boxed construction
Precision MIG welded

The post KINETIK Rear Chassis Upper & Lower Link Mounts first appeared on Camburg Engineering.

KINETIK Prerunner/Race Front Suspension Bulkhead Kit

scott — Tue, 15 Jun 2021 20:08:29 +0000

Building a pre-runner or race truck from the ground up or looking to upgrade your existing truck? Our KINETIK front suspension bulkhead kit takes the headache out of designing the front of the truck; after all it’s one of the most complicated aspects to the truck. We designed this based around our proven TT/6100 chassis and geometry and gives you a great starting point to build from or easily graft into an existing tube chassis or frame rails. By MIG welding this we’re able to bring the cost down and offer something a little more affordable without compromising quality or the components. We put just as much attention and detail into this setup as our top level platforms. Suspension pivot points are FK 1″ and 1.50″ uniballs and 7/8″ heims, we don’t use cheap delrin bushings. The steering uses FK 7/8″ and 1″ heims with our billet machined tie rods that tie into our steering rack adapter. We blanchard grind the bulkhead where the steering rack mounts after welding for the perfect fit, which most companies don’t do. This insures the the rack sits perfectly flat and isn’t put into a bind when bolted down which increases wear and tear on the internal components. We also supply you with all 12 point & hex MS/NAS aircraft bolts and hardware for the utmost strength and precision with their properly shouldered grip lengths. This setup is above and beyond many of the competitors out there.

CAD designed and laser cut
4130 chromoly tubing & plate
Precision MIG welded
Blanchard ground steering rack mounting surface
24″ useable wheel travel
Designed for 3.0 x 14″ coilovers and 4.0 x 14″ bypass shocks
76.5″ WMS with Camburg 2.50 hub kit (91-92″ total width with 37-40″ tires)
All MS/NAS aircraft hardware supplied

We also offer a fully TIG welded and heat-treated version. If you’re looking for something a little more complete, we also offer our chassis platforms in various configurations that have the engine cage and upper shock mounts setup along with 2.5 air bump mounts.

The post KINETIK Prerunner/Race Front Suspension Bulkhead Kit first appeared on Camburg Engineering.

KINETIK Prerunner/Race Rear Fuel Cell Basket

scott — Tue, 25 May 2021 23:12:20 +0000

Building a pre-runner or race truck from the ground up or looking to upgrade your existing truck? Our new KINETIK rear fuel cell basket and custom Pyrotect fuel cells are the perfect combo and take the headache out of designing the rear of the truck. We designed this based around our TT/6100 chassis and geometry but with a rear fuel cell position and dual horizontal spares. We offer two different fuel cells based on your needs and our basket design is already setup for our KINETIK 24″ sway-bar system. It comes standard MIG welded but we can also multi-pass TIG weld it like our KINETIK TT/6100 chassis’s and suspension. For you “do it yourselfers” and welding guru’s we can also sell it just tacked together for you.

CAD designed and laser cut
4130 chromoly tubing
MIG, Multi-pass TIG or DIY “Tacked” welding options
Setup for dual horizontal spares (37-40″ tires)
Integrated sway-bar mounting & fuel cell hold downs
24″ KINETIK sway-bar arms and 300M sway-bar (optional)
Custom Pyrotect 95-100 gallon fuel cells (optional)
See “WHAT’S INCLUDED” for fuel cell and sway-bar details/options

The post KINETIK Prerunner/Race Rear Fuel Cell Basket first appeared on Camburg Engineering.

KINETIK Prerunner/Race MIG Truck Chassis Platform

scott — Wed, 07 Oct 2020 21:53:55 +0000

The post KINETIK Prerunner/Race MIG Truck Chassis Platform first appeared on Camburg Engineering.